We are in the process of migrating this forum. A new space will be available soon. We are sorry for the inconvenience.

ks28192.kimsufi.com festplatte scheint defekt zu sein.


Stefan
06.03.14, 18:52
Das Ticket wurde erstellt, bitte dein Backup im Ticket bestätigen.

darscht
06.03.14, 15:07
disk 2:
smartctl 5.41 2011-06-09 r3365 [x86_64-linux-3.10.23-xxxx-std-ipv6-64-rescue] (local build)
Copyright (C) 2002-11 by Bruce Allen, http://smartmontools.sourceforge.net

=== START OF INFORMATION SECTION ===
Device Model: TOSHIBA DT01ACA050
Serial Number: 233D0SUPS
LU WWN Device Id: 5 000039 ff2efbdd9
Firmware Version: MS1OA750
User Capacity: 500,107,862,016 bytes [500 GB]
Sector Sizes: 512 bytes logical, 4096 bytes physical
Device is: Not in smartctl database [for details use: -P showall]
ATA Version is: 8
ATA Standard is: ATA-8-ACS revision 4
Local Time is: Thu Mar 6 14:35:06 2014 CET
SMART support is: Available - device has SMART capability.
SMART support is: Enabled

=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: FAILED!
Drive failure expected in less than 24 hours. SAVE ALL DATA.
See vendor-specific Attribute list for failed Attributes.

General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 5128) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: ( 86) minutes.
SCT capabilities: (0x003d) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.

SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000b 093 093 016 Pre-fail Always - 458776
2 Throughput_Performance 0x0005 095 095 054 Pre-fail Offline - 542
3 Spin_Up_Time 0x0007 135 135 024 Pre-fail Always - 180 (Average 159)
4 Start_Stop_Count 0x0012 100 100 000 Old_age Always - 14
5 Reallocated_Sector_Ct 0x0033 001 001 005 Pre-fail Always FAILING_NOW 1925
7 Seek_Error_Rate 0x000b 100 100 067 Pre-fail Always - 0
8 Seek_Time_Performance 0x0005 110 110 020 Pre-fail Offline - 36
9 Power_On_Hours 0x0012 099 099 000 Old_age Always - 8241
10 Spin_Retry_Count 0x0013 100 100 060 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 14
192 Power-Off_Retract_Count 0x0032 094 094 000 Old_age Always - 7569
193 Load_Cycle_Count 0x0012 094 094 000 Old_age Always - 7569
194 Temperature_Celsius 0x0002 193 193 000 Old_age Always - 31 (Min/Max 21/39)
196 Reallocated_Event_Count 0x0032 001 001 000 Old_age Always - 2444
197 Current_Pending_Sector 0x0022 100 100 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0008 100 100 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x000a 200 200 000 Old_age Always - 0

SMART Error Log Version: 1
ATA Error Count: 47 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.

Error 47 occurred at disk power-on lifetime: 8238 hours (343 days + 6 hours)
When the command that caused the error occurred, the device was active or idle.

After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 08 60 12 00 00 Error: UNC at LBA = 0x00001260 = 4704

Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 08 00 60 12 00 40 00 12:40:48.778 READ FPDMA QUEUED
ef 10 02 00 00 00 a0 00 12:40:48.778 SET FEATURES [Reserved for Serial ATA]
27 00 00 00 00 00 e0 00 12:40:48.778 READ NATIVE MAX ADDRESS EXT
ec 00 00 00 00 00 a0 00 12:40:48.776 IDENTIFY DEVICE
ef 03 46 00 00 00 a0 00 12:40:48.775 SET FEATURES [Set transfer mode]

Error 46 occurred at disk power-on lifetime: 8238 hours (343 days + 6 hours)
When the command that caused the error occurred, the device was active or idle.

After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 08 60 12 00 00 Error: UNC at LBA = 0x00001260 = 4704

Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 08 08 60 12 00 40 00 12:40:43.392 READ FPDMA QUEUED
60 00 00 00 13 00 40 00 12:40:43.392 READ FPDMA QUEUED
ef 10 02 00 00 00 a0 00 12:40:43.391 SET FEATURES [Reserved for Serial ATA]
27 00 00 00 00 00 e0 00 12:40:43.391 READ NATIVE MAX ADDRESS EXT
ec 00 00 00 00 00 a0 00 12:40:43.389 IDENTIFY DEVICE

Error 45 occurred at disk power-on lifetime: 8238 hours (343 days + 6 hours)
When the command that caused the error occurred, the device was active or idle.

After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 a0 60 12 00 00 Error: UNC at LBA = 0x00001260 = 4704

Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 00 08 00 13 00 40 00 12:40:33.703 READ FPDMA QUEUED
60 00 00 00 12 00 40 00 12:40:33.703 READ FPDMA QUEUED
60 00 00 00 10 00 40 00 12:40:33.701 READ FPDMA QUEUED
60 08 00 00 40 28 40 00 12:40:16.809 READ FPDMA QUEUED
60 08 00 08 40 28 40 00 12:40:16.809 READ FPDMA QUEUED

Error 44 occurred at disk power-on lifetime: 8223 hours (342 days + 15 hours)
When the command that caused the error occurred, the device was active or idle.

After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
10 51 68 b8 aa 4c 01 Error: IDNF at LBA = 0x014caab8 = 21801656

Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
61 08 00 c0 6f 84 40 00 01:30:43.861 WRITE FPDMA QUEUED
61 08 00 b8 6f 84 40 00 01:30:38.407 WRITE FPDMA QUEUED
61 88 18 00 20 45 40 00 01:30:38.361 WRITE FPDMA QUEUED
61 10 10 a8 6f 84 40 00 01:30:38.361 WRITE FPDMA QUEUED
61 e0 08 40 aa 4c 40 00 01:30:38.361 WRITE FPDMA QUEUED

Error 43 occurred at disk power-on lifetime: 8223 hours (342 days + 15 hours)
When the command that caused the error occurred, the device was active or idle.

After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
10 51 88 98 aa 4c 01 Error: IDNF at LBA = 0x014caa98 = 21801624

Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
61 88 00 00 20 45 40 00 01:30:31.726 WRITE FPDMA QUEUED
61 08 00 a0 6f 84 40 00 01:30:31.534 WRITE FPDMA QUEUED
61 e0 10 40 aa 4c 40 00 01:30:31.518 WRITE FPDMA QUEUED
61 d8 08 c8 b6 44 40 00 01:30:31.518 WRITE FPDMA QUEUED
61 10 00 90 6f 84 40 00 01:30:31.518 WRITE FPDMA QUEUED

SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Short offline Completed without error 00% 8 -
# 2 Short offline Completed without error 00% 3 -
# 3 Short offline Completed without error 00% 3 -

SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.

darscht
06.03.14, 15:06
disk 1:
smartctl 5.41 2011-06-09 r3365 [x86_64-linux-3.10.23-xxxx-std-ipv6-64-rescue] (local build)
Copyright (C) 2002-11 by Bruce Allen, http://smartmontools.sourceforge.net

=== START OF INFORMATION SECTION ===
Device Model: TOSHIBA DT01ACA050
Serial Number: 233D0RRPS
LU WWN Device Id: 5 000039 ff2efbdb7
Firmware Version: MS1OA750
User Capacity: 500,107,862,016 bytes [500 GB]
Sector Sizes: 512 bytes logical, 4096 bytes physical
Device is: Not in smartctl database [for details use: -P showall]
ATA Version is: 8
ATA Standard is: ATA-8-ACS revision 4
Local Time is: Thu Mar 6 14:35:01 2014 CET
SMART support is: Available - device has SMART capability.
SMART support is: Enabled

=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: FAILED!
Drive failure expected in less than 24 hours. SAVE ALL DATA.
See vendor-specific Attribute list for failed Attributes.

General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 5225) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: ( 87) minutes.
SCT capabilities: (0x003d) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.

SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000b 099 099 016 Pre-fail Always - 65537
2 Throughput_Performance 0x0005 109 109 054 Pre-fail Offline - 193
3 Spin_Up_Time 0x0007 133 133 024 Pre-fail Always - 184 (Average 161)
4 Start_Stop_Count 0x0012 100 100 000 Old_age Always - 14
5 Reallocated_Sector_Ct 0x0033 001 001 005 Pre-fail Always FAILING_NOW 1945
7 Seek_Error_Rate 0x000b 100 100 067 Pre-fail Always - 0
8 Seek_Time_Performance 0x0005 113 113 020 Pre-fail Offline - 35
9 Power_On_Hours 0x0012 099 099 000 Old_age Always - 8241
10 Spin_Retry_Count 0x0013 100 100 060 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 14
192 Power-Off_Retract_Count 0x0032 096 096 000 Old_age Always - 5177
193 Load_Cycle_Count 0x0012 096 096 000 Old_age Always - 5177
194 Temperature_Celsius 0x0002 200 200 000 Old_age Always - 30 (Min/Max 21/38)
196 Reallocated_Event_Count 0x0032 001 001 000 Old_age Always - 2753
197 Current_Pending_Sector 0x0022 100 100 000 Old_age Always - 8
198 Offline_Uncorrectable 0x0008 100 100 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x000a 200 200 000 Old_age Always - 0

SMART Error Log Version: 1
ATA Error Count: 163 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.

Error 163 occurred at disk power-on lifetime: 8229 hours (342 days + 21 hours)
When the command that caused the error occurred, the device was active or idle.

After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
10 51 b8 28 c0 49 01 Error: IDNF at LBA = 0x0149c028 = 21610536

Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 20 10 40 b4 49 40 00 03:47:59.749 READ FPDMA QUEUED
61 c0 08 20 c0 49 40 00 03:47:59.749 WRITE FPDMA QUEUED
61 08 00 88 42 84 40 00 03:47:59.749 WRITE FPDMA QUEUED
ef 10 02 00 00 00 a0 00 03:47:59.749 SET FEATURES [Reserved for Serial ATA]
27 00 00 00 00 00 e0 00 03:47:59.749 READ NATIVE MAX ADDRESS EXT

Error 162 occurred at disk power-on lifetime: 8229 hours (342 days + 21 hours)
When the command that caused the error occurred, the device was active or idle.

After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
10 51 c0 20 c0 49 01 Error: IDNF at LBA = 0x0149c020 = 21610528

Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 20 00 40 b4 49 40 00 03:47:56.548 READ FPDMA QUEUED
60 c0 18 40 01 48 40 00 03:47:56.547 READ FPDMA QUEUED
60 80 10 a0 00 48 40 00 03:47:56.547 READ FPDMA QUEUED
60 20 08 60 00 48 40 00 03:47:56.547 READ FPDMA QUEUED
60 40 00 00 00 48 40 00 03:47:56.547 READ FPDMA QUEUED

Error 161 occurred at disk power-on lifetime: 8229 hours (342 days + 21 hours)
When the command that caused the error occurred, the device was active or idle.

After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
10 51 c0 20 c0 49 01 Error: IDNF at LBA = 0x0149c020 = 21610528

Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 c0 40 e0 17 4d 40 00 03:47:54.333 READ FPDMA QUEUED
60 20 38 a0 17 4d 40 00 03:47:54.333 READ FPDMA QUEUED
60 60 30 20 17 4d 40 00 03:47:54.333 READ FPDMA QUEUED
60 c0 28 00 2a 4d 40 00 03:47:54.332 READ FPDMA QUEUED
60 20 20 c0 29 4d 40 00 03:47:54.332 READ FPDMA QUEUED

Error 160 occurred at disk power-on lifetime: 8229 hours (342 days + 21 hours)
When the command that caused the error occurred, the device was active or idle.

After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
10 51 c0 20 c0 49 01 Error: IDNF at LBA = 0x0149c020 = 21610528

Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
61 10 20 78 42 84 40 00 03:47:53.142 WRITE FPDMA QUEUED
60 20 00 e0 29 4d 40 00 03:47:52.094 READ FPDMA QUEUED
61 40 18 c0 9c 4c 40 00 03:47:52.072 WRITE FPDMA QUEUED
61 e0 10 e0 98 4c 40 00 03:47:52.072 WRITE FPDMA QUEUED
61 c0 08 20 c0 49 40 00 03:47:52.072 WRITE FPDMA QUEUED

Error 159 occurred at disk power-on lifetime: 8229 hours (342 days + 21 hours)
When the command that caused the error occurred, the device was active or idle.

After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
10 51 c0 20 c0 49 01 Error: IDNF at LBA = 0x0149c020 = 21610528

Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 20 40 40 b0 49 40 00 03:47:49.915 READ FPDMA QUEUED
61 20 38 80 50 48 40 00 03:47:49.915 WRITE FPDMA QUEUED
61 20 30 40 51 48 40 00 03:47:49.915 WRITE FPDMA QUEUED
61 20 28 80 57 48 40 00 03:47:49.915 WRITE FPDMA QUEUED
61 c0 20 20 c0 49 40 00 03:47:49.914 WRITE FPDMA QUEUED

SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Short offline Completed without error 00% 8 -
# 2 Short offline Completed without error 00% 3 -
# 3 Short offline Completed without error 00% 3 -

SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.

darscht
06.03.14, 14:56
screenshot

http://darscht.de/cgchdgfe.png

Marcel40625
06.03.14, 14:52
screenshots... smartlogs etc ... ohne nachweise wirst du kein ticket bekommen ... so gehts schneller

darscht
06.03.14, 14:49
Haben den Server ins rescue-mode gestartet, dort wird angezeigt, dass eine oder mehrere Festplatte defekt seien. Dort steht: Smart State: error.

wenn ich per SSH fsck starte, meldet es viele defekte dateien.

Vielen Dank!