OVH Community, your new community space.

HDD Defekt 16G


Stefan
03.02.14, 18:07
Ticket wurde erstellt, bitte im Ticket bestätigen.

filu
03.02.14, 13:46
Hallo, seit kurzen hab ich Probleme, dass das System in Read Only geht. Datensicherung für 30 GB hat über 24 Stunden gedauert da immer wieder die HDD Geschwindigkeitseinbrüche auf ca 10 kb/s hatte.

Datacenter: rbx2
Rack: 24A08
Nummer: 358437

hier der log von smartctl:

root@rescue:~# smartctl -a /dev/sda
smartctl 5.41 2011-06-09 r3365 [x86_64-linux-3.10.23-xxxx-std-ipv6-64-rescue] (l ocal build)
Copyright (C) 2002-11 by Bruce Allen, http://smartmontools.sourceforge.net

=== START OF INFORMATION SECTION ===
Device Model: TOSHIBA DT01ACA200
Serial Number: 73PT52SKS
LU WWN Device Id: 5 000039 ff3d91383
Firmware Version: MX4OABB0
User Capacity: 2,000,398,934,016 bytes [2.00 TB]
Sector Sizes: 512 bytes logical, 4096 bytes physical
Device is: Not in smartctl database [for details use: -P showall]
ATA Version is: 8
ATA Standard is: ATA-8-ACS revision 4
Local Time is: Mon Feb 3 14:35:46 2014 CET
SMART support is: Available - device has SMART capability.
SMART support is: Enabled

=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: FAILED!
Drive failure expected in less than 24 hours. SAVE ALL DATA.
See vendor-specific Attribute list for failed Attributes.

General SMART Values:
Offline data collection status: (0x84) Offline data collection activity
was suspended by an interrupting command from host.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: (14918) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off supp ort.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: ( 249) minutes.
SCT capabilities: (0x003d) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.

SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_ FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000b 085 085 016 Pre-fail Always - 590075
2 Throughput_Performance 0x0005 100 100 054 Pre-fail Offline - 200
3 Spin_Up_Time 0x0007 135 135 024 Pre-fail Always - 280 (Average 282)
4 Start_Stop_Count 0x0012 100 100 000 Old_age Always - 26
5 Reallocated_Sector_Ct 0x0033 001 001 005 Pre-fail Always FAILI NG_NOW 1998
7 Seek_Error_Rate 0x000b 100 100 067 Pre-fail Always - 0
8 Seek_Time_Performance 0x0005 124 124 020 Pre-fail Offline - 33
9 Power_On_Hours 0x0012 100 100 000 Old_age Always - 3672
10 Spin_Retry_Count 0x0013 100 100 060 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 26
192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 30
193 Load_Cycle_Count 0x0012 100 100 000 Old_age Always - 30
194 Temperature_Celsius 0x0002 171 171 000 Old_age Always - 35 (Min/Max 25/45)
196 Reallocated_Event_Count 0x0032 001 001 000 Old_age Always - 2286
197 Current_Pending_Sector 0x0022 100 100 000 Old_age Always - 40
198 Offline_Uncorrectable 0x0008 100 100 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x000a 200 200 000 Old_age Always - 0

SMART Error Log Version: 1
ATA Error Count: 35 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.

Error 35 occurred at disk power-on lifetime: 3225 hours (134 days + 9 hours)
When the command that caused the error occurred, the device was active or idle .

After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 08 30 ae b0 0a Error: UNC at LBA = 0x0ab0ae30 = 179351088

Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 08 00 30 ae b0 40 00 00:57:48.175 READ FPDMA QUEUED
ef 10 02 00 00 00 a0 00 00:57:48.175 SET FEATURES [Reserved for Serial A TA]
27 00 00 00 00 00 e0 00 00:57:48.175 READ NATIVE MAX ADDRESS EXT
ec 00 00 00 00 00 a0 00 00:57:48.174 IDENTIFY DEVICE
ef 03 46 00 00 00 a0 00 00:57:48.174 SET FEATURES [Set transfer mode]

Error 34 occurred at disk power-on lifetime: 3225 hours (134 days + 9 hours)
When the command that caused the error occurred, the device was active or idle .

After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 08 30 ae b0 0a Error: UNC at LBA = 0x0ab0ae30 = 179351088

Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 08 00 30 ae b0 40 00 00:57:44.415 READ FPDMA QUEUED
ef 10 02 00 00 00 a0 00 00:57:44.415 SET FEATURES [Reserved for Serial A TA]
27 00 00 00 00 00 e0 00 00:57:44.415 READ NATIVE MAX ADDRESS EXT
ec 00 00 00 00 00 a0 00 00:57:44.414 IDENTIFY DEVICE
ef 03 46 00 00 00 a0 00 00:57:44.414 SET FEATURES [Set transfer mode]

Error 33 occurred at disk power-on lifetime: 3225 hours (134 days + 9 hours)
When the command that caused the error occurred, the device was active or idle .

After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 08 30 ae b0 0a Error: UNC at LBA = 0x0ab0ae30 = 179351088

Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 08 00 30 ae b0 40 00 00:57:40.664 READ FPDMA QUEUED
ef 10 02 00 00 00 a0 00 00:57:40.664 SET FEATURES [Reserved for Serial A TA]
27 00 00 00 00 00 e0 00 00:57:40.664 READ NATIVE MAX ADDRESS EXT
ec 00 00 00 00 00 a0 00 00:57:40.663 IDENTIFY DEVICE
ef 03 46 00 00 00 a0 00 00:57:40.662 SET FEATURES [Set transfer mode]

Error 32 occurred at disk power-on lifetime: 3225 hours (134 days + 9 hours)
When the command that caused the error occurred, the device was active or idle .

After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 08 30 ae b0 0a Error: UNC at LBA = 0x0ab0ae30 = 179351088

Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 08 00 30 ae b0 40 00 00:57:36.904 READ FPDMA QUEUED
ef 10 02 00 00 00 a0 00 00:57:36.904 SET FEATURES [Reserved for Serial A TA]
27 00 00 00 00 00 e0 00 00:57:36.904 READ NATIVE MAX ADDRESS EXT
ec 00 00 00 00 00 a0 00 00:57:36.903 IDENTIFY DEVICE
ef 03 46 00 00 00 a0 00 00:57:36.903 SET FEATURES [Set transfer mode]

Error 31 occurred at disk power-on lifetime: 3225 hours (134 days + 9 hours)
When the command that caused the error occurred, the device was active or idle .

After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 08 28 ae b0 0a Error: UNC at LBA = 0x0ab0ae28 = 179351080

Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 08 00 28 ae b0 40 00 00:57:33.144 READ FPDMA QUEUED
ef 10 02 00 00 00 a0 00 00:57:33.144 SET FEATURES [Reserved for Serial A TA]
27 00 00 00 00 00 e0 00 00:57:33.144 READ NATIVE MAX ADDRESS EXT
ec 00 00 00 00 00 a0 00 00:57:33.143 IDENTIFY DEVICE
ef 03 46 00 00 00 a0 00 00:57:33.143 SET FEATURES [Set transfer mode]

SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA _of_first_error
# 1 Short offline Completed without error 00% 95 -
# 2 Short offline Completed without error 00% 87 -
# 3 Short offline Completed without error 00% 5 -

SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.


lg und vielen dank im voraus