We are in the process of migrating this forum. A new space will be available soon. We are sorry for the inconvenience.

Festplatte defekt!?


hemmerseb
02.12.13, 09:13
Hallo oglx,

soeben wurde ein Störungsticket erstellt. Bitte gemäß der verschickten E-Mail noch einmal im Störungsticket antworten bzw. bestätigen, dass ein Backup der Daten vorhanden ist und ein Eingriff erfolgen kann. Ohne weitere Rückmeldung im Ticket kann leider kein Eingriff durchgeführt werden.

Sebastian

oglx
02.12.13, 08:43
Hallo,

seit einiger Zeit habe ich Probleme auf meinem Server (ks3359889). Ich habe gesehen, dass die Platten als ReadOnly gemounted sind. Soft Reboot funktioniert nicht und gibt nur die Meldung "Eingabe-/Ausgabefehler" aus. Ich habe Netboot ausgeführt und der SMART-Test zeigt die unten angefügte Meldung an. Könnte bitte jemand einen Blick drauf werfen und evtl. einen HDD-Tausch veranlassen?

Danke sehr!
Viele Grüße!

smartctl 5.41 2011-06-09 r3365 [x86_64-linux-3.10.9-xxxx-std-ipv6-64-rescue] (local build)
Copyright (C) 2002-11 by Bruce Allen, http://smartmontools.sourceforge.net

=== START OF INFORMATION SECTION ===
Device Model: TOSHIBA DT01ACA050
Serial Number: 5345DVANS
LU WWN Device Id: 5 000039 ff6d08d98
Firmware Version: MS1OA750
User Capacity: 500,107,862,016 bytes [500 GB]
Sector Sizes: 512 bytes logical, 4096 bytes physical
Device is: Not in smartctl database [for details use: -P showall]
ATA Version is: 8
ATA Standard is: ATA-8-ACS revision 4
Local Time is: Fri Nov 29 11:27:28 2013 CET
SMART support is: Available - device has SMART capability.
SMART support is: Enabled

=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: FAILED!
Drive failure expected in less than 24 hours. SAVE ALL DATA.
See vendor-specific Attribute list for failed Attributes.

General SMART Values:
Offline data collection status: (0x84) Offline data collection activity
was suspended by an interrupting command from host.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 5192) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: ( 87) minutes.
SCT capabilities: (0x003d) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.

SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000b 100 100 016 Pre-fail Always - 0
2 Throughput_Performance 0x0005 135 135 054 Pre-fail Offline - 96
3 Spin_Up_Time 0x0007 131 131 024 Pre-fail Always - 184 (Average 166)
4 Start_Stop_Count 0x0012 100 100 000 Old_age Always - 11
5 Reallocated_Sector_Ct 0x0033 001 001 005 Pre-fail Always FAILING_NOW 92
7 Seek_Error_Rate 0x000b 099 099 067 Pre-fail Always - 1
8 Seek_Time_Performance 0x0005 113 113 020 Pre-fail Offline - 35
9 Power_On_Hours 0x0012 100 100 000 Old_age Always - 2237
10 Spin_Retry_Count 0x0013 100 100 060 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 11
192 Power-Off_Retract_Count 0x0032 099 099 000 Old_age Always - 1323
193 Load_Cycle_Count 0x0012 099 099 000 Old_age Always - 1323
194 Temperature_Celsius 0x0002 206 206 000 Old_age Always - 29 (Min/Max 24/36)
196 Reallocated_Event_Count 0x0032 100 100 000 Old_age Always - 120
197 Current_Pending_Sector 0x0022 001 001 000 Old_age Always - 12672
198 Offline_Uncorrectable 0x0008 001 001 000 Old_age Offline - 213987
199 UDMA_CRC_Error_Count 0x000a 200 200 000 Old_age Always - 0

SMART Error Log Version: 1
ATA Error Count: 6 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.

Error 6 occurred at disk power-on lifetime: 2236 hours (93 days + 4 hours)
When the command that caused the error occurred, the device was active or idle.

After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 08 f8 1c 80 02 Error: UNC at LBA = 0x02801cf8 = 41950456

Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 08 00 f8 1c 80 40 00 00:01:25.998 READ FPDMA QUEUED
ef 10 02 00 00 00 a0 00 00:01:25.998 SET FEATURES [Reserved for Serial ATA]
27 00 00 00 00 00 e0 00 00:01:25.998 READ NATIVE MAX ADDRESS EXT
ec 00 00 00 00 00 a0 00 00:01:25.996 IDENTIFY DEVICE
ef 03 46 00 00 00 a0 00 00:01:25.996 SET FEATURES [Set transfer mode]

Error 5 occurred at disk power-on lifetime: 2236 hours (93 days + 4 hours)
When the command that caused the error occurred, the device was active or idle.

After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 08 f8 1c 80 02 Error: UNC at LBA = 0x02801cf8 = 41950456

Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 08 00 f8 1c 80 40 00 00:01:23.251 READ FPDMA QUEUED
ef 10 02 00 00 00 a0 00 00:01:23.251 SET FEATURES [Reserved for Serial ATA]
27 00 00 00 00 00 e0 00 00:01:23.251 READ NATIVE MAX ADDRESS EXT
ec 00 00 00 00 00 a0 00 00:01:23.249 IDENTIFY DEVICE
ef 03 46 00 00 00 a0 00 00:01:23.249 SET FEATURES [Set transfer mode]

Error 4 occurred at disk power-on lifetime: 2236 hours (93 days + 4 hours)
When the command that caused the error occurred, the device was active or idle.

After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 00 1d 80 02 Error: UNC at LBA = 0x02801d00 = 41950464

Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 08 08 f8 1c 80 40 00 00:01:19.890 READ FPDMA QUEUED
60 00 00 00 1d 80 40 00 00:01:19.890 READ FPDMA QUEUED
ef 10 02 00 00 00 a0 00 00:01:19.889 SET FEATURES [Reserved for Serial ATA]
27 00 00 00 00 00 e0 00 00:01:19.889 READ NATIVE MAX ADDRESS EXT
ec 00 00 00 00 00 a0 00 00:01:19.887 IDENTIFY DEVICE

Error 3 occurred at disk power-on lifetime: 2236 hours (93 days + 4 hours)
When the command that caused the error occurred, the device was active or idle.

After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 08 f8 1c 80 02 Error: UNC at LBA = 0x02801cf8 = 41950456

Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 00 00 00 1c 80 40 00 00:01:17.166 READ FPDMA QUEUED
60 00 08 00 1b 80 40 00 00:01:17.166 READ FPDMA QUEUED
60 00 00 00 1a 80 40 00 00:01:17.165 READ FPDMA QUEUED
60 00 08 00 19 80 40 00 00:01:17.164 READ FPDMA QUEUED
60 00 00 00 18 80 40 00 00:01:17.163 READ FPDMA QUEUED

Error 2 occurred at disk power-on lifetime: 2236 hours (93 days + 4 hours)
When the command that caused the error occurred, the device was active or idle.

After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 08 00 20 80 02 Error: UNC at LBA = 0x02802000 = 41951232

Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 08 00 00 20 80 40 00 00:00:46.601 READ FPDMA QUEUED
ef 10 02 00 00 00 a0 00 00:00:46.599 SET FEATURES [Reserved for Serial ATA]
27 00 00 00 00 00 e0 00 00:00:46.599 READ NATIVE MAX ADDRESS EXT
ec 00 00 00 00 00 a0 00 00:00:46.597 IDENTIFY DEVICE
ef 03 46 00 00 00 a0 00 00:00:46.597 SET FEATURES [Set transfer mode]

SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Short offline Completed without error 00% 29 -
# 2 Short offline Completed without error 00% 26 -
# 3 Short offline Completed without error 00% 8 -
# 4 Short offline Completed without error 00% 2 -

SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.